1. Home
  2. Getting Started
  3. PTZ Camera Quick Setup Guide

PTZ Camera Quick Setup Guide

Intro

Get your Honey Optics camera running on your network (Quick Setup)

If you purchased a Honey Optics camera you most likely purchased it for it’s IP/Network  capability. One of the best ways to use the Honey Optics PTZ cameras is via the Network/IP connection. You can still use the HDMI, USB 3.0, or SDI outputs if you’d like, however this quick start guide will focus mostly on the network/IP setup.

Why Choose Video over IP/Network?

Video over network is great for multiple reasons. First you can get the live image feed to any computer or device on the network. Not only can get the video on multiple devices on the network, but you can also control the PTZ camera from any device on your network.

Unpacking

Your camera will arrive with the following contents.

Upon arrival please inspect the box and make sure everything is included.

Contents:
1x – PTZ 4K UHD Camera from Honey Optics
1x – IR Handheld Wireless Remote
1x – AC Power Adaptor
1x – Power Cable
1x – RS232 Cable
1x – User Manual

Powering Up

If the network cable that you will be connecting to is not powered (PoE) you will need to  connect the camera to external power using the Power Adaptor and Cable to power up the camera.

Connect the power cable turn the power switch to ON

Connecting the camera to your Network

Plug camera into your network switch / router

Using an Ethernet cable connect the camera to an active network port on your network. (If your switch provides PoE, do not use external power adaptor).

Your network port can be a on network switch or a router

Finally power on your camera.

Find camera on your network using the Upgrade Tool

Next using the buttons below download our Upgrade tool. Available for both Windows and Mac computers.

The Upgrade tool will help you find the camera you on your network and allow you to set the IP address and settings.

Download UPGRADE Tool

The software downloads as a ZIP file. Will need to be un-zipped/un-archived before you can run it.

Once you run the program you should be able to select different NIC network ports on your computer located top right near INTERFACE.

Select the Network port area where the camera was connected to.

After selecting the proper network connection click the SEARCH button, and then wait for the tool to populate all the IP devices on the network.

NOTE: The Default IP address on the camera is 192.168.100.88

Once you found the camera. Most likely with IP address 192.168.100.88 you can right click on the camera to reveal a menu option.

Click Config and you’ll get a options panel where you can change the IP address of the camera.

Setting IP Address

The next step is to change the camera’s IP address to be in the same IP range as your network/router.

As mentioned before the camera comes with a default static IP address of 192.168.100.88.

You will need to change that to be in the same range as your network.

This should be the first (3) octet/sets of numbers from the interface you are using the find the cameras.

For example the network used in the set up to be 192.168.2.xxx

So in this case I would change the IP address of the camera from 192.168.100.88 to something like 192.168.2.88 (as long as the the first 3 octets/sets of numbers are the same as the network, the last set is customizable to whatever you’d like)

You should be able to leave the NetMask alone unless there is a reason for you to change it. The Gateway should be the same as the IP address you used, but .1 instead of the last set of digits in your IP address. So, in my example above, 192.168.2.100 IP address should have 192.168.2.1 as the gateway.

After changing the settings to make sure to click SET

Camera will reboot and the newly set IP address will be now saved.

NOTE

In a more complex network setting and environment you may have to request a “STATIC IP” from your IT department to prevent any possible complications on your network in addition to the appropriate Network Mask, Default Gateway and First DNS for that Static IP

Accessing Camera Settings

Now that the camera’s IP is set to our network we can access the camera setting GUI (graphical user interface) via a web browser such as Chrome, FireFox, Edge, or Safari.

In your browser type in the camera’s new IP address.

In my case that would be 192.168.2.100

You will be prompted for a Username and Password, both are “admin” by default.

Once signed in you will see the Graphical User Interface (GUI) with a live feed coming in from the camera.

On the left you will see the PTZ controls and preset options.

From here you can adjust the PTZ control settings, and also go into each submenu to adjust different camera settings and options.

Using PTZ Controls

There are a few ways to controlling your Honey Optics PTZ camera.

Using your computer to control is one of the most cost effective and easiest options.

NDI / RMTSP Setup

Once the Camera is on your network you will be able to use the NDI feature.

NDI has their own software that you can use to control the camera and have a live feed from the camera.

Visit NDI Tools to download Windows or Mac software

Stream and/or Record!

You are now ready to Stream or Record your events!

Bringing in the feed into your favorite streaming software is easy.

Resources: OBS NDI Plugin (view your camera stream right in OBS)

Updated on September 2, 2021

Was this article helpful?